Looking for:

Force Windows 7, 8, or 10 to Boot Into Safe Mode Without Using the F8 Key.

Click here to Download


Important If the computer is connected to a network, network policy settings might prevent you from following these steps. Only use the System Configuration utility to change the advanced boot options on the computer with guidance from a Microsoft support engineer. Using the System Configuration utility might make the computer unusable.

Under Startup in Task Manager , for each startup item, select the item and then select Disable. When you restart the computer, it’s in a clean boot environment. Follow troubleshooting steps to install, uninstall, or run your application.

Your computer might temporarily lose some functionality while in a clean boot environment. Reset the computer to start normally after clean boot troubleshooting and resume functionality. Swipe in from the right edge of the screen, and then select Search.

Type msconfig in the search box, and then select msconfig. Select Startup in Task Manager, then for each startup item, select the item and then select Disable. The computer restarts in a clean boot environment. Your computer might temporarily lose some functionality while in a clean boot environment, however that functionality will return.

Finish troubleshooting and reset the computer to start normally. Select Start , type msconfig. Note If you’re prompted for an administrator password or for confirmation, type the password or provide confirmation. On the General tab, select Selective startup , and then deselect Load startup items. The Use Original Boot. On the Services tab, select Hide all Microsoft services , and then select Disable all. Note This step lets Microsoft services continue to run.

If you disable these services, you might permanently delete all restore points. Do not do this if you want to use the System Restore utility together with existing restore points. Select OK , and then select Restart. After you restart the computer, you’ll have a clean boot environment. Then, do one of the following, as appropriate for your situation:. Note If you receive the “The Windows Installer service could not be accessed” error during the installation or uninstallation, you’ll need more information.

How to start the Windows Installer service when system services are not loaded. Then install or uninstall the program or update again. If the installation or uninstallation is successful, you issue is resolved and you can start as you usually do.

How to reset the computer to start as usual. If the installation or uninstallation still fails, that means this issue is not caused by application or service interference. You mght need to contact the program manufacturer for more specific support.

If the program runs correctly, this issue is caused by application or service interferences. You can find out which application or service is causing the issue. How to determine what is causing the issue by performing a clean boot If the program still doesn’t run as expected, this issue is not caused by application or service interference.

You might need to contact the program manufacturer for more specific support. If your problem does not occur while the computer is in a clean boot environment, then you can determine which startup application or service is causing the problem by systematically turning them on or off and restarting the computer. While turning on a single service or startup item and rebooting each time will eventually find the problematic service or application, the most efficient way to do this is to test half of them at a time, thus eliminating half of the items as the potential cause with each reboot of the computer.

You can then repeat this process until you’ve isolated the problem. Here’s how:. Sign in to the computer by using an account that has administrator rights. For Windows 10, in the search box on the taskbar, type msconfig. In Windows 8 or 8. In the search box, type msconfig. Select msconfig or System Configuration from the search results. Select Services , and then select Hide all Microsoft services. Select each of the check boxes in the upper half of the Service list.

If the problem still occurs, one of the checked items is the problematic service. Repeat steps 1 through 6, but in Step 5, clear the lower half of the boxes in the Service list that you selected in your last test. Starts Windows domain controller running Active Directory so that the directory service can be restored. Debugging Mode. Starts Windows in an advanced troubleshooting mode intended for IT professionals and system administrators. Disable automatic restart on system failure. Prevents Windows from automatically restarting if an error causes Windows to fail.

Choose this option only if Windows is stuck in a loop where Windows fails, attempts to restart, and fails again repeatedly. Disable Driver Signature Enforcement. Allows drivers containing improper signatures to be installed. Start Windows Normally. Starts Windows in its normal mode. Windows 7 More Need more help? Join the discussion. Was this information helpful?

Yes No. Thank you! Any more feedback? The more you tell us the more we can help. Can you help us improve? Resolved my issue. Home Windows General Windows How-tos. How to reboot into Safe Mode at a command prompt. General Windows Windows 7. Mac Mad This person is a verified professional. Verify your account to enable IT peers to see that you are a professional. Sep 26, 2 Minute Read. Reply 9. Facebook Twitter Reddit LinkedIn. Kevin Billington This person is a verified professional. Main Areas of Contribution:.

Track Progress. Earn Credits. Below are instructions for Windows 7 and XP. Step Reboot the computer, which will start in the mode you chose is step 2.



Windows 7 professional safe mode with command prompt free –

1. Start command prompt from Windows 7 System Recovery Options, which you ever used to get in Windows 7 safe mode in method 2. 2. Type following command and press Enter. bcdedit /deletevalue {default} safeboot. 3. Restart Windows 7 and computer will exit safe mode and start normally. Have successfully entered or exited safe mode in Windows 7? Aug 20,  · I choose “Safe mode with Command prompt”. But instead of displaying me the command prompt on the login screen it shows me the normal login screen. windows loads files but does not show the dos screen even if i choose simple ‘safe mode’ option. What should I do to resolve the issue? I want the command prompt. Apr 25,  · Get a Safe Command Prompt Outside of Windows. Start with your PC on. Hold down the power button on your computer for 10 seconds—your PC will turn off. Press the power button again to turn the PC back on. As soon as the computer turns back on (you’ll usually see the manufacturer’s logo), press and Views: K.




Comments are closed